By Instruction for Installing a Bathtub
By Instruction for Installing a Bathtub
Blog Article
Everyone has got their own individual theory about Installing A Bathtub.
Mounting a bath tub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard project. If the old tub is easily easily accessible, the task can move easily; if you need to open a wall surface to eliminate the old bathtub as well as place the new tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will require a helper to leave the old bathtub and also set in the brand-new one. Make sure you have certified on your own for the job as well as fit trying it. Rather than hiring a service provider to take over a halfway-completed project, it is much better to take into consideration employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will certainly assist you set up a brand-new bathtub in your restroom if you have actually currently acquired a new bathtub and don't need to transform the setup of your previous supply of water pipelines.
Your devices and material list should make up the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be quite troublesome as a result of the restricted gain access to that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before moving on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Protect the faucet in place with the maker given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The previous type should be attached to the tap ends initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are helpful in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the bath tub till the level reads degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leakages and also tighten them if needed. Fill up the bathtub as well as likewise inspect the overflow outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bath tub needs to wait up until the tub has actually been used a minimum of once as this will certainly settle it right into its final position.
Planning for the Installment
First of all, the supporting framework supplied with the bathroom must be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to prevent pressure on the bathtub.
Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a rigid seal, causing the water to pass through the wall in between the bathroom as well as the tiling, resulting in difficulties with dampness and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components and fittings. They are sold in tubes and cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can crack rather early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the market. It is suggested to fit the floor tiles using water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very fascinated with How to Install a Bathtub Yourself and I hope you appreciated our piece. Sharing is caring. Helping others is fun. Thank you for your time. Visit us again soon.
Secure your plumbing. Report this page